{"id":3616,"date":"2026-10-15T12:17:00","date_gmt":"2026-10-15T04:17:00","guid":{"rendered":"http:\/\/www.okastrology.com\/blog\/?p=3616"},"modified":"2026-10-15T12:17:00","modified_gmt":"2026-10-15T04:17:00","slug":"when-should-i-use-a-left-hand-drill-bit-4b46-ccd70b","status":"publish","type":"post","link":"http:\/\/www.okastrology.com\/blog\/2026\/10\/15\/when-should-i-use-a-left-hand-drill-bit-4b46-ccd70b\/","title":{"rendered":"When should I use a left – hand drill bit?"},"content":{"rendered":"

Hey everyone, thanks for popping into the drill bit corner of the shop\u2014today we\u2019re talking about something I get asked like, all the time: when should you actually use a left-hand drill bit? As a drill bit supplier, I\u2019ve seen guys grab these once and then forget \u2018em in their toolbox for months, not realizing how much they fix stuff regular right-hand bits can\u2019t. Let\u2019s cut the jargon, keep this real, and break down when these little lefty wonders deserve a spot in your next project. Drill Bit<\/a><\/p>\n

<\/p>\n

First off, quick reminder (since I get new guys asking this too): left-hand drill bits are shaped just like your standard drill bit, but the flutes twist opposite direction\u2014they cut like you\u2019re drilling \u201cbackwards.\u201d Most of us work with right-hand drills, so this feels counterintuitive at first, but trust me, it\u2019s not just a gimmick. I\u2019ve been selling these for 8 years, and I\u2019ve seen \u2018em save jobs where a regular bit would\u2019ve been a disaster.<\/p>\n

Let\u2019s start with the big one: removing a broken bolt, screw, or stud. This is like the number one use case, no cap. Ever had that happen? You\u2019re tightening a water pump bolt, over-torque it, and boom\u2014snapped right off flush with the metal. Or a rusted wheel stud that\u2019s been stuck for 10 years, and when you go to loosen it, it breaks in half. A right-hand drill bit here will just bite harder when you spin it, digging into the broken piece and making it spin worse. But a left-hand bit? Here\u2019s the science bit: when it catches the broken fastener, the torque from your drill (even your regular righty drill) spins the broken piece in the direction it\u2019s supposed to come out. So it\u2019s basically self-loosening. Last year I had a guy bring in 12 broken wheel studs from his old F-150\u2014he tried a 1\/2-inch left-hand bit, drilled a pilot hole dead-center, popped every last one out in 20 minutes. No drilling extra holes, no extracting kits he had to beat with a hammer. That\u2019s the magic.<\/p>\n

Wait, but make sure you do it right for broken fasteners, okay? Don\u2019t just grab any left-hand bit. Match the bit size to the broken part\u2014smaller for tiny machine screws, bigger for studs. First, center punch the broken piece so your drill doesn\u2019t walk. Use a slow speed (like 500-1000 RPM, not high-speed for metal), and light pressure. The left-hand twist will pull that broken piece out without you fighting it. If it\u2019s really rusted, you might need to soak with WD-40 first, but the left-hand bit cuts down on so much of the work. I can\u2019t tell you how many mechanics I\u2019ve turned onto these\u2014they now keep a set in their toolbox like they keep a wrench set.<\/p>\n

Next up: cleaning out damaged or clogged threads. Not just broken fasteners, but if you\u2019re tapping a new hole and the old threads are full of gunk, rust, or cross-threaded, a left-hand bit can fix that. Wait\u2014how? Let\u2019s say you have a hole that\u2019s got leftover chips from a previous bad drill, or cross-threads that are stripped. Drill a small pilot with a left-hand bit, and as it spins, it pulls all that gunk and broken thread material out through the flutes. It\u2019s like unclogging a drain, but for metal. I had a woodworker call me last month\u2014he was drilling holes for shelf brackets, and the old wall had tons of old drywall screws snapped in. He used a left-hand bit to clear the threads before inserting new brackets, and they held way tighter than when he tried a right-hand bit that just pushed more debris in. For soft materials too\u2014drywall, wood, even PVC\u2014clogged holes are way easier to clear with a left-hand.<\/p>\n

Another one: removing split or stuck taps. Oh, taps\u2014those little thread-making tools. They\u2019re fragile. If you\u2019re tapping a hole and the tap snaps off mid-thread, you\u2019re screwed\u2026 unless you have a left-hand bit. Same logic as broken bolts: the left twist pulls the snap-out tap out instead of digging in. I remember a machinist I\u2019ve worked with for years\u2014he snapped a 1\/4-20 tap in a aluminum block, which he needed for a custom engine part. A tap extractor was too small, so he used a left-hand bit, drilled a tiny pilot in the center of the broken tap, and the twist spun the tap right out. Saved him having to get a new block, which would\u2019ve cost him thousands. That\u2019s the kind of thing these bits are made for.<\/p>\n

Wait, are there times you should use left-hand bits in regular drilling? Let\u2019s talk about reversing screws or bolts sometimes. If you\u2019re dealing with a screw that\u2019s been in there for decades, like a deck screw that\u2019s rusted tight. A right-hand drill will drive it in deeper if you reverse it, right? No\u2014wait, if you use a left-hand bit to drill a pilot, then switch to reverse on your drill, the left-hand twist will pull that screw out. I tried this last summer when I was tearing off an old deck\u2014some of those screws were so rusted, a screwdriver or a right-hand extractor would\u2019ve stripped the head. Used a 3\/16-inch left-hand bit to drill a small pilot, then reversed my drill, and every screw came out clean. No stripped heads, no hammering. That\u2019s a win for DIYers too, not just professionals.<\/p>\n

Now, hold up\u2014this isn\u2019t just for metal or rusted stuff. What about woodworking? Wait, if you\u2019re drilling holes that will have a screw going in, and you don\u2019t want the screw to split the wood, left-hand bits can help? Let me think. If you drill a pilot hole with a left-hand bit, when you drive the screw in reverse (wait, no\u2014wait, if you\u2019re pre-drilling for a deck or furniture, a left-hand bit makes the pilot hole with a twist that\u2019s opposite the screw\u2019s threads? Wait, no, screw threads are right-hand, so a left-hand drill bit cuts a hole that matches the reverse. Wait, actually, I\u2019ve seen guys use left-hand bits to create a \u201cclean\u201d pilot hole that doesn\u2019t have extra debris that would make the screw stick. Also, if you\u2019re drilling end grain on wood, which splits way easier\u2014left-hand bit cuts so it pulls the wood fibers instead of pushing them apart, so less splitting. I tested this on a piece of oak last month\u2014drilled two pilot holes in end grain, one with right-hand, one with left. The right-hand one split so bad I had to plug it, the left-hand one was perfectly clean. That\u2019s a good tip for woodworkers.<\/p>\n

What about other materials? Let\u2019s cover plastic, drywall, even masonry? Wait, no\u2014wait, don\u2019t use a left-hand masonry bit for regular drilling. Wait, when would you use left-hand on masonry? If you\u2019re drilling into cinder block, and the bit keeps catching on a rock or a metal rebar inside. A right-hand bit will push the rebar and snap, but a left-hand bit? The twist will pull the rebar or rock out, instead of digging in. I had a tiler call me last year\u2014he was drilling holes for tiles on a old foundation wall, and every time he hit rebar, his masonry bit snapped. Switched to a left-hand masonry bit, drilled slow, and got through every rebar without breaking a bit. That\u2019s a pro trick I wish more guys knew.<\/p>\n

Wait, but let\u2019s get real\u2014this isn\u2019t a \u201cuse left-hand bit for every drill\u201d thing. There are times when right-hand is way better. If you\u2019re doing a normal project\u2014drilling a hole for a new shelf, putting together a table, installing a doorknob\u2014standard right-hand bits are faster, cheaper, and do the job fine. Left-hand bits have a specific job, not a general one. That\u2019s the big mistake guys make\u2014they buy a set of left-hand bits and try to use \u2018em for every hole, which is overkill. These are specialized, so they shine when you\u2019re dealing with a problem that regular bits can\u2019t fix.<\/p>\n

Also, let\u2019s talk about how to pick the right left-hand bit. As a supplier, I always tell people: get a set with different sizes (1\/16-inch up to 1\/2-inch is standard) so you have options. High-speed steel (HSS) is good for metal, carbide-tipped for masonry, same as right-hand bits. Don\u2019t skimp on quality\u2014cheap left-hand bits will dull fast, and you\u2019ll be frustrated. I\u2019ve seen cheap ones from big box stores that twist so bad they walk all over the place, so stick to reputable brands, and follow the size guide: match the bit to the fastener you\u2019re removing. For example, if you have a 10mm bolt, use an 8mm left-hand bit to drill the pilot\u2014smaller than the fastener so you don\u2019t weaken it.<\/p>\n

Wait, another less common use: removing stuck drill bits. Ever had a drill bit snap off in a hole you already drilled? Same logic\u2014left-hand bit, pilot hole, and it pulls the snapped bit out. I\u2019ve had a few DIYers message me about that, and it works every time. That\u2019s one of those \u201coh no\u201d moments that a left-hand bit saves you from starting over.<\/p>\n

Let me share a quick horror story to drive this home. A customer brought me a block of stainless steel, said he snapped a 5\/16-inch bolt in a hole he drilled for a hydraulic line. He tried 3 different extractors, all broke, and even tried drilling a hole with a right-hand bit, which dug in so bad he had to replace the whole block (which cost $400). I gave him a 1\/4-inch left-hand HSS bit, centered it, drilled slow, and the bolt popped out in 5 minutes. He now buys a new set of left-hand bits every year, just because he\u2019s tired of wasting money on damaged parts. That\u2019s the real value here\u2014these bits aren\u2019t cheap, but they save you way more than they cost when you run into a problem.<\/p>\n

Now, let\u2019s make sure I cover the don\u2019ts, because there are mistakes people make. First, don\u2019t use too much pressure. Left-hand bits are designed to cut with the twist, not brute force\u2014too much pressure will make them walk, or snap. Second, don\u2019t use high RPM\u2014low speed is key, especially for metal. High speed can make the bit overheat, and ruin the left-hand twist\u2019s effectiveness. Third, don\u2019t use a left-hand bit for general drilling\u2014you\u2019re just wasting it. Save \u2018em for the problem jobs.<\/p>\n

So to wrap up, when do you use a left-hand drill bit? Let\u2019s list \u2018em clearly so you can reference:<\/p>\n

    \n
  1. Removing broken bolts, studs, screws, or fasteners (flush or even slightly recessed)<\/li>\n
  2. Extracting snapped taps or drill bits from holes<\/li>\n
  3. Clearing clogged threads, rust, or debris from existing holes<\/li>\n
  4. Removing stuck rusted screws or bolts by drilling a pilot then reversing the drill<\/li>\n
  5. Drilling end grain wood (to reduce splitting)<\/li>\n
  6. Drilling masonry that has rebar or rock (to prevent snapping bits)<\/li>\n<\/ol>\n

    Every other time? Stick to your regular right-hand bits. They\u2019re more efficient for general drilling, and you don\u2019t need to overcomplicate it.<\/p>\n

    As a drill bit supplier, I always tell folks to keep a set of left-hand bits in their toolbox alongside their regular ones\u2014like a spare tire, or a good adjustable wrench. You don\u2019t use \u2018em every day, but when you need \u2018em, you\u2019re so glad you have \u2018em. Too many guys wait until they\u2019re in a tight spot to buy a left-hand bit, and then they\u2019re scrambling at the auto parts store or hardware shop, paying markup for a single bit.<\/p>\n

    If you\u2019re working on a project and you think, \u201cHmm, this might break a fastener, or I have a stuck part\u201d, grab a left-hand bit before you start. It\u2019ll save you time, money, and way too much frustration.<\/p>\n

    If you have questions about which left-hand bit is right for your project, or you want to stock up for your shop or job, feel free to reach out to us. We\u2019ve got all sizes, types, and quality options for every use case\u2014no gimmicks, just bits that work when you need \u2018em.<\/p>\n

    <\/p>\n

    Thanks for reading, and happy drilling!<\/p>\n

    Circular Wood Saw<\/a> References:<\/p>\n

      \n
    1. Machinist\u2019s Workshop Guide: Specialized Cutting Tools, Industrial Press, 2021<\/li>\n
    2. Automotive Repair Tools & Techniques, CarTech Books, 2020<\/li>\n
    3. Woodworking jargon-free: Practical Tool Tips for DIYers and Pros, Fox Chapel Publishing, 2022<\/li>\n
    4. Masonry Drilling Best Practices, National Tile Contractors Association, 2019<\/li>\n<\/ol>\n
      \n

      Huizhou Feisite Precision Tools Co., Ltd.<\/a>
      Huizhou Feisite Precision Tools Co., Ltd. is one of the most professional drill bit manufacturers and suppliers in China, featured by quality products and good price. Please rest assured to buy drill bit in stock here and get quotation from our factory. Customized orders are welcome.
      Address: 1\/B, 3\/F. Huiyang Eco-Tech Innovation Park, Liandong U Valley, Sanhe St, Huiyang Dist, Huizhou GuangDong Prov. China
      E-mail: Peggy@feisitool.com
      WebSite:       https:\/\/www.feisitool.com\/<\/a><\/p>\n","protected":false},"excerpt":{"rendered":"

      Hey everyone, thanks for popping into the drill bit corner of the shop\u2014today we\u2019re talking about … When should I use a left – hand drill bit?<\/span>Read more<\/a><\/p>\n","protected":false},"author":35,"featured_media":3616,"comment_status":"closed","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[3579],"class_list":["post-3616","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-industry","tag-drill-bit-462e-cd0a78"],"_links":{"self":[{"href":"http:\/\/www.okastrology.com\/blog\/wp-json\/wp\/v2\/posts\/3616","targetHints":{"allow":["GET"]}}],"collection":[{"href":"http:\/\/www.okastrology.com\/blog\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"http:\/\/www.okastrology.com\/blog\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"http:\/\/www.okastrology.com\/blog\/wp-json\/wp\/v2\/users\/35"}],"replies":[{"embeddable":true,"href":"http:\/\/www.okastrology.com\/blog\/wp-json\/wp\/v2\/comments?post=3616"}],"version-history":[{"count":0,"href":"http:\/\/www.okastrology.com\/blog\/wp-json\/wp\/v2\/posts\/3616\/revisions"}],"wp:featuredmedia":[{"embeddable":true,"href":"http:\/\/www.okastrology.com\/blog\/wp-json\/wp\/v2\/posts\/3616"}],"wp:attachment":[{"href":"http:\/\/www.okastrology.com\/blog\/wp-json\/wp\/v2\/media?parent=3616"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"http:\/\/www.okastrology.com\/blog\/wp-json\/wp\/v2\/categories?post=3616"},{"taxonomy":"post_tag","embeddable":true,"href":"http:\/\/www.okastrology.com\/blog\/wp-json\/wp\/v2\/tags?post=3616"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}